Page 3 of 3 FirstFirst 123
Results 31 to 35 of 35
  1. #31
    4 Star Lounger Coochin's Avatar
    Join Date
    Jun 2014
    Location
    Queensland, Australia
    Posts
    578
    Thanks
    6
    Thanked 56 Times in 54 Posts
    Quote Originally Posted by rstew View Post
    Remember, these are core temps, NOT case temps!

    rstew
    "core temps" are the important numbers. Core temps above about 70C "when working" are getting into dangerous territory. If they go above 80C it is very likely to cause damage, especially to components near the CPU socket. Ideally your core temps should stay below 70C even under full load.

    See "Heavyload" at http://www.jam-software.de/heavyload/ and "Speedfan" at http://www.almico.com/speedfan.php (both are very good and free). You need to run system under full load for at least 30min - if any core temp goes over 80C then look at replacing the CPU cooler fan/heatsink with a high capacity unit (e.g.: Coolermaster Hyper 212 EVO; Thermaltake ISGC-200 or ISGC-400.

    2GB DDR2 RAM is a bit light on for Win7. If you have 1x2GB chip you should look at adding another compatible 2GB chip (you may have other options depending on number of RAM slots on board). This should allow your memory bus to run in dual-channel mode (allows multi-core CPU better use of RAM).

    Common problem w/ RAM is tarnished contacts (tarnish builds up over a period of time, especially in humid weather). Easily cleaned off by gently rubbing the contacts with a good-quality white pencil rubber, then use a clean dry toothbrush or similar to remove any leftover particles.

    Computer Consultant/Technician 15+ years experience.
    Last edited by Coochin; 2014-07-03 at 21:03.

  2. #32
    2 Star Lounger
    Join Date
    Jun 2014
    Posts
    110
    Thanks
    4
    Thanked 2 Times in 2 Posts
    Coochin,
    I appreciate your comments re core temps.
    I have just started using SpeedFan, and I notice right away that it reports core temps that are consistently 10 to 15 degrees cooler than what RealTemp reports.
    So now I am not sure what to believe.
    I would like to believe the lower temps are correct, but who knows?

    Anyone else using both RealTemp and SpeedFan, and what core temp comparisons do you see?

    rstew

  3. #33
    Silver Lounger
    Join Date
    Aug 2012
    Location
    UK
    Posts
    2,239
    Thanks
    37
    Thanked 298 Times in 289 Posts
    You could check to see what temps the free version of Speccy and HWMonitor give and compare those with what RealTemp and SpeedFan gives.

    https://www.piriform.com/speccy

    http://www.cpuid.com/softwares/hwmonitor.html

  4. #34
    4 Star Lounger wavy's Avatar
    Join Date
    Dec 2009
    Location
    ny
    Posts
    425
    Thanks
    39
    Thanked 17 Times in 17 Posts
    Or try a quick trip to the BIOS if it reports temps
    David

    Just because you don't know where you are going doesn't mean any road will get you there.

  5. #35
    2 Star Lounger
    Join Date
    Jun 2014
    Posts
    110
    Thanks
    4
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by wavy View Post
    Or try a quick trip to the BIOS if it reports temps
    Good suggestion, but alas, the bios reports only board, MCH, and ICH temps!

    rstew

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •